Introduction: Seamless underwear and sportswear lines need a TPU hot melt powder that keeps stretch recovery, soft hand feel, and wash resistance in balance, so the first trial should match grade choice to fabric heat sensitivity and the target laundry cycle.
These requirements interact in the bond line; they are not separate choices. Before sampling a seamless underwear or sportswear program, the practical choice is whether to start with a low-temperature soft grade that protects delicate elastic fabric or move to a higher-melt grade built for 60℃ wash programs. The wrong first trial often shows up as curled seams, a stiff waistband, or edge lift after the first wash cycle. A grade that feels perfect on the table may fail a 60℃ laundry test, while a highly wash-resistant grade can leave a bond line that is too firm for intimate apparel. AY-6985, AY-6995, and AY-6920 fit different stretch-fabric scenarios, so the trial should begin with the fabric, the wash brief, and the line conditions in mind.
Why treating elasticity and wash resistance separately leads to bonding failures
Seamless underwear and sportswear depend on fabric that stretches, recovers, and stays smooth against the body. The adhesive layer has to move with that fabric. When a bonding project is planned around only softness or only wash resistance, the trial can look good in one test and fail in another. A low-temperature grade may protect the fabric and keep the seam soft, but it may not hold through a 60℃ wash program. A higher-melt grade may pass a hotter wash test, but the higher activation temperature can stiffen heat-sensitive nylon/spandex blends, create thermal shrinkage, or leave a hard edge that customers feel immediately. The real failure mode is a mismatch between the adhesive’s elastic recovery, the fabric’s modulus, and the wash cycle. Wash resistance depends on thermal stability in the bond line as well as powder add-on and pressure. The bond line needs enough thermal stability to survive the wash, and enough flexibility to stretch with the garment without cracking or lifting. For a 40℃ wash brief, AY-6985 can support a soft hand feel with a recommended bonding range of 90–120℃ and 5–10 seconds. For a 60℃ wash brief, AY-6995 and AY-6920 are better starting points because they combine excellent 40℃ wash performance with good 60℃ wash performance. When these goals are treated separately, production trials tend to repeat without settling on a stable grade.

How to match TPU powder melting range and particle size to stretch fabrics
DSC melting range tells you how much heat the powder needs to flow and form a bond. Particle size tells you how the powder lands, melts, and penetrates. On stretch fabrics, the goal is a continuous, flexible adhesive film that follows the fabric’s movement. If the powder is too fine for a heavy add-on, coverage can be thin. If the powder is too coarse for a fine bond line, the seam may feel lumpy or show through. TPU hot melt powder is available from 0–80 μm to 300–600 μm, so the right starting point depends on the scatter unit, target add-on, and the bond line required. An 80–200 μm or 80–300 μm grade often gives a practical balance for many textile lamination lines, while finer grades support thinner, more controlled deposits.
1. How Low Activation Grades Protect Heat-Sensitive Elastic Fabrics
AY-6985 has a DSC range of 70–80℃ and a recommended bonding range of 90–120℃, with a dwell time of 5–10 seconds. That lower activation window is valuable for thin nylon/spandex, mesh, and other stretch fabrics that can shrink, curl, or lose recovery when exposed to higher heat. The lower temperature also helps the bond line stay soft, which matters in waistbands, side seams, and edge bonding where a stiff adhesive can be felt through the fabric. In reference lab tests, AY-6985 rates Good at 40℃ wash. It is the grade to trial when the garment’s wash brief is 40℃ and the priority is fabric protection, softness, and elastic recovery. If the program later moves to 60℃, the project should switch to a higher-melt grade rather than push AY-6985 outside its intended range.
2. How Higher Wash Grades Support 60℃ Laundry Programs
AY-6995 and AY-6920 are the main choices for seamless underwear and sportswear that must handle 60℃ wash programs. AY-6995 has a DSC range of 95–105℃ and a recommended bonding range of 110–140℃, with 8–12 seconds of dwell time. It rates Excellent at 40℃ and Good at 60℃ in reference lab tests. AY-6920 has a DSC range of 110–120℃ and a recommended bonding range of 120–150℃, with 8–15 seconds. It also rates Excellent at 40℃ and Good at 60℃. The higher melting range gives the bond line more thermal stability through the wash cycle, but the fabric must handle the higher activation temperature without losing stretch or surface quality. If the program also needs 90℃ wash data, AY-6920-M and AY-6930-M move into the discussion. AY-6920-M is rated Satisfactory at 90℃, and AY-6930-M is rated Good at 90℃ in reference lab tests. Both require higher bonding temperatures, so check fabric heat sensitivity first.
What Aoyu Model Data Offers for Seamless Underwear Trials
Model data provides a starting matrix for matching grades to wash briefs and fabric limits. For a 40℃ wash brief on heat-sensitive elastic fabric, AY-6985 is the natural first trial. For a 60℃ wash brief, AY-6995 is often the practical first step because it balances a lower activation range with good 60℃ wash performance. AY-6920 offers a higher melting range and more thermal stability when the fabric can handle 120–150℃ bonding. When the project includes higher wash temperatures, AY-6920-M and AY-6930-M provide the next level of wash resistance data, with AY-6930-M rated Good at 90℃ in lab tests. These ratings are lab references; actual results depend on fabric, blend, lamination, and wash cycle. The fastest way to turn model data into a production decision is to prepare a trial with real fabric and real wash conditions. Share the fabric composition, stretch direction, elastic recovery, fabric weight, heat sensitivity, and the exact wash program needed. Also share the scatter unit, target particle size, line speed, pressure range, dwell time, and target add-on. For these trials, Aoyu acts as a TPU hot melt adhesive powder manufacturer with deep cryogenic grinding for particle sizes from 0–80 μm to 300–600 μm, and can provide custom TPU hot melt adhesive powder for specific line conditions. The company also serves as a TPU hot melt adhesive powder supplier for seamless underwear, sportswear, and interlining projects, backed by OEKO-TEX Standard 100, ISO9001, and ISO14001 certifications. Send fabric samples and the wash target to get a focused grade recommendation and sample direction.
Conclusion
For seamless underwear and sportswear, the grade choice should follow the wash brief and the fabric’s heat limit together. AY-6985 is the low-temperature soft option for heat-sensitive elastic fabrics and 40℃ wash programs. AY-6995 and AY-6920 are better starting points for 60℃ wash requirements, with AY-6920 giving more thermal stability when the fabric can handle the higher bonding range. AY-6920-M and AY-6930-M support higher 60℃ and 90℃ wash discussions. Before committing to a production grade, prepare fabric samples, target temperature-pressure-dwell conditions, particle size, and the actual wash cycle the garment must pass. Aoyu can review those details and recommend a sample direction for the line.
FAQ
Q: Which TPU hot melt powder grade is suitable for seamless underwear with 60℃ wash requirements?
A: For a 60℃ wash requirement, start with AY-6995 or AY-6920. Both are rated Excellent at 40℃ and Good at 60℃ in reference lab tests. AY-6995 uses a recommended bonding range of 110–140℃ and 8–12 seconds, while AY-6920 uses 120–150℃ and 8–15 seconds. If the fabric is heat-sensitive, test AY-6995 first. If the brief also needs 90℃ wash data, review AY-6920-M or AY-6930-M and confirm fabric heat tolerance before sampling.
Q: How does activation temperature affect elastic fabric hand feel in seamless bonding?
A: Activation temperature affects how much heat the stretch fabric sees and how the adhesive layer forms. A lower range such as 90–120℃ with AY-6985 helps protect thin nylon/spandex, mesh, and other heat-sensitive fabrics, keeping the seam soft and flexible. Higher-melt grades such as AY-6995 and AY-6920 need 110–150℃ and give better 60℃ wash performance, but they can stiffen or distort a heat-sensitive fabric if the temperature is not matched to the material. Match the grade to the fabric first, then dial in pressure and dwell time.
Q: What fabric and wash details should I provide before testing elastic TPU adhesive powder?
A: Provide the fabric composition, spandex content, fabric weight, stretch direction, elastic recovery, surface finish, and heat sensitivity. For the wash test, share the target wash temperature, number of cycles, detergent type, drying method, and any shrinking or edge-lift issue seen in current samples. For the line, share the scatter unit, target particle size, line speed, pressure range, dwell time, and target add-on. With those details, a starting grade such as AY-6985, AY-6995, AY-6920, or a higher wash model can be recommended and a more focused sample trial prepared.
Sources / References
Resources – Advanced Textiles Association
Green Guides | Federal Trade Commission
